• Controller Octopus Pro 1.0 F446 https://github.com/bigtreetech/BIGTREETECH-OCTOPUS-Pro

• AntHead
  • DELTA ASB02505SHA-A 5V Hotend Fan
  • GDSTIME 4010 12000RPM 24V Blower Part Cooling Fans
  • Chirpy's Alt X-Carriage
• WristWatch Galileo 2 (WWG2)
• Rapido HF 1.0
  • 0.4mm Nozzle - Hardened Steel Bondtech CHT
  • 0.6mm Nozzle - Hardened Steel
• Toolhead Board EBB36 V1.1 G0B1 https://github.com/bigtreetech/EBB
• CAN Bus

• MeanWell UHP200-24 PSU

• Kirigami Bed
• 100W 24V DC Keenovo Bed Heater
• WAGOs

• Fermio Labs YZ-Rails
• HIWIN X-Rail

• Mesh Skirts
• Mesh Electronics and Bottom Cover
• Hex Deck and Back Panels
• Wide Guitar Amp Feet - Customised for M5 Nuts
• Monolith Clear Polycarbonate Side Panels
• Dual Rear 608 Spool Rollers
• Mellow Daylight on a Matchstick (10 RGB LEDs)
  • Customised Mounts

• Overture ASA Light Grey
• Overture ABS Diamond Grey
• Bambu Labs ASA-CF Black

CLICK HERE TO DOWNLOAD THE ENTIRE REPO

You can Download JUST the STL folder by clicking HERE

Printed Parts Guide

The official release of the Voron Zero 3D printer. You can find the BOM in the configurator located at the Voron Design website.

The current revision is V0.2r1

• Compact and portable
• 120x120x120 build volume
• CoreXY
• Low mass direct drive extruder
• Enclosed chamber
• 24v DC bed
• Klipper firmware
• Filament runout sensor

Skirts

• We fixed the issue where 34mm Z motors didnt fit in the machine with the bottom panel installed, this involved increasing the height of the skirts/feet by 2mm
• We added a simple filament runout sensor to the rear right foot

Toolhead

• Mini Stealthburner direct drive and bowden cowling part cooling ducts improved
• an issue with the guidler being able to pivot in an undesired direction was addressed by tightening the bolt holes to reduce play
• RIDGA support for the bearings that come stock with the ridga kit has been added

Tophat

• cam locks for the tophat were changed to a simple hex key design

Z Endstop

• z endstop mount was beefed up to improve ridgidity

BOM Changes

the BOM increased by the following items

• 2x m2x10 self tapping screw
• 1x MR85 bearing
• 1x Microswitch
• 1x ECAS04 Bowden Collet

A majority of the printed parts have changed. The configurator will give you an idea of parts needed if you are upgrading from V0.1.

Toolhead

• New design: Mini Stealthburner
• Direct Drive Extruder with BMG gears and 20mm thick pancake motor with 10 tooth spur gear
• Improved part cooling ducts (fans are same as V0.1)
• Supports Revo VORON, Dragon, Dragonfly BMO, DropEffect XG, Creality Spider Pro

Drive units

• Motor screw count reduction
• Endstop removed for sensorless homing

Frame

• No changes

Tophat

• All panels have changed
• All side panels are identical
• Extrusion based tophat
• Hinged design
• Cam locks to secure tophat in place

Panels/Clips

• All panels are 3mm
• Deck panel changed, new panel is not required
• Split rear panel

X/Y Joints

• Tops became 1mm smaller to accommodate MiniSB
• Endstop block removed for sensorless homing

Bed Assembly

• Printed parts changed, bed position moved 3mm to the rear

Feet/Skirts

• Trident skirt community mod folded into official release

Front Idlers

• Cam locks added

See https://github.com/VoronDesign/Voron-0/releases/tag/V0.1

See https://github.com/VoronDesign/Voron-0/releases/tag/V0.0r1

See https://github.com/VoronDesign/Voron-0/releases/tag/V0.0